Frig bob saws
The single-hand stone saw known to quarrymen and masons as a frig bob typically had a heavy rigid blade ranging from 5 ft to 7 ft (1.5m to 2.1m) long and when new was 9 inches (225 mm), or more, in depth with a peg tooth profile teeth at a pitch of 5/8 inch (15.87 mm).
For sawing blind cuts in the rock, it was found advantageous to file in an extra tooth or two around the front of the saw. At the other end an eye hole attachment was riveted to the blade – a simple ash stick inserted in the eye hole sufficed for a handle.
When were frig bobs first used in the Bath stone quarries? The very late 1830s seems probable. Work began on Randell, Saunders & Co’s Corsham Down (Tunnel) Quarry in 1839. A careful search of the area around the foot of the slope shaft in 2006 only found evidence of cutting with frig bobs. In Godwin’s Westwood Quarry a “May 1840” graffito conveniently dates the first frig bob sawn pillar. A sale of railway contractors plant at Box held in August 1841 included stone saws and other quarry tools. At Farleigh Down Quarry an “1845” graffito written on an early frig bob sawn pillar could suggest that the changeover to sawing varied from quarry to quarry by several years.
Frig bob saws were also used at Dundry Somerset around c1855, at Beer Quarry, Devon from the late 1880s and at Weldon Quarry, Northamptonshire, also from the late 1880s. Although saw cuts were started by sawing horizontally, the saw was quickly worked into a sloping mode so that the front end of the saw cut was deeper than the back end. To prevent the saw dust from clogging the saw, it was necessary to add water from a drip tin. This was usually an old tin with a small hole in the side just above the bottom – a match stick placed in the hole conducted the water to the saw cut. The resulting slurry was swilled out of the cut by the back stroke of the saw.
The hardness of Bath stone varies between the different beds and quarries; roughly it took an hour to saw a vertical depth of 1 foot over a length of 5 feet or so. In the mid 1950s drills powered by compressed air were introduced to two quarries. It was found that by drilling a series of deep holes at roughly 3 to 4 inches pitch along the line of an intended saw cut, that hand sawing was greatly speeded up. This practice ended with the closures of Hartham Park Quarry in 1960 and Clift Quarry in 1968.
The sawyer stood or sat directly behind the saw blade which was lined up with the middle of his chest. The saw was held with both hands and the effort shared equally by both arms. But this symmetrical mode was not possible when sawing pillar cuts: the arm nearest the pillar did more of the work. Pillars of unhewn stone are left to support the ground above.
Frig bob sawing
Marshall Cole the ganger (LH) and Reg Pashley (RH) sawing with
frig bobs at Hartham Park Quarry in the 1950s.
Frig bob vertical
Jack Osbourne sawing vertically with a frig bob, note the back of
the saw is sliding against a pick head, his feet are standing on
the pick helve. Hartham Park Quarry 1950s.
New pillar cuts were offset by a few inches to give clearance for the saw handle and the sawyer’s hand. This offset is known as a hatch. To prevent chaffing against the pillar, sawyers wrapped a strip of cloth or a short length of old bicycle inner tube around the knuckles of the hand nearest to the pillar. To avoid the stone breaking off short when it was subsequently raised, i.e. wristing off, it was necessary, when making a pillar cut, to aw to the bottom of the bed without taking a break.
Frig bob saw-teeth needed regular sharpening and setting, For sharpening the saw was inserted upside down into a saw cut in the top of a saw stone or bench; the sharpening was done with a triangular file, starting at one end of the saw, filing one side of each tooth in turn with one pass of the file until the other end of the saw was reached. The saw was then turned around and the process repeated on the other side of each tooth. The front angle of the teeth was filed straight across at right angles to the blade. The files were supplied by W. Tyzack, Sons & Turner, Ltd. of Sheffield. Sometime in the early post war period a saw sharpening machine was bought from Thomas Robinson & Sons Ltd of Rochdale, this machine used a veeprofile carborundum wheel to sharpen the teeth.
Saw Sharpener
The vee profiled carborundum wheel of the Thomas
Robinson & Sons Ltd saw sharpening machine.
Repeated sharpening over a long period reduced the depth of a frig bob to around 4 inches (100 mm), this was then known as a razzer or bacon slasher; razzer is believed to be a dialect word meaning worn out. These worn saws had a specialised role for making saw cuts in the jad (the horizontal slot picked out under the ceiling and above the stone being sawn).
Frig bob & razzer
Keith Palmer holding a razzer (left) and a
frig bob (right), note the opening hammer
lying on the floor. Keith started work in Clift
Quarry at Box in 1968 and spent his first
two weeks sawing with a frig bob.
Razzer in jad
Starting a back cut with a razzer, the quarryman is sitting
in the wrist hole vacated by the wrist stone; Hartham Park Quarry 1950s.
For setting the teeth, i.e. splaying the teeth slightly outwards in alternate directions so that they made a cut a little wider than the thickness of the blade, the saw teeth edge of the blade was laid along the head of a rail. The rail acted as a former whilst every other tooth was opened or bent outwards with an opening hammer. The saw was then turned over and the process repeated on every other tooth. This gave clearance so that the main part of the blade was clear of the sides of the cut. Care was taken to work from the base of the tooth towards the point to avoid breaking it. The opening hammer seems to have been a locally made tool.
Opening hammer
Setting the teeth with an opening hammer
There are a few references to suppliers and makers of stone saws.
In a series of three advertisements addressed to Quarry masters and Builders, G T Robbins, a Bradford on Avon ironmonger, advertised cast-steel stone saws on 27th March 1875.
The Winding Up Accounts of Randell Saunders & Co. Ltd includes two payments “For Saws”. In 1887 they paid £8-7-3d to G & T Gray and in 1888 £10-15-6d was paid to Spafford & Co.
Throughout the 1890s, the Directors of the Bath Stone Firms Ltd authorised payments to G & T Gray, A Spafford & Co and W Tyzack, Sons & Turner Ltd, what the payments were for was not recorded but could have been for saws and saw sharpening files.
Early Sheffield directories list several members of the Gray family engaged in the metal trades. Thomas Gray was a saw maker in 1834, a scissor smith in 1839 and a saw manufacturer in 1841. George Gray was manufacturing pen knives in 1839 and 1841, and Jonathan Gray & Sons were manufacturing saws at 36 Malinda Street in 1841. By 1849 George and Thomas Gray were trading as saw manufacturers at 36 Malinda Street, also known as the Australia Saw Works from the 1880s, in 1901 their products included files. G & T Gray were incorporated with John Elsworth & Sons, Ltd. around 1905, but the G. & T. Gray name continued to be listed until 1923, at least.
Abraham Spafford was listed amongst the gentry in 1834, as a bookkeeper in 1841 and as a saw manufacturer in 1849. A Spafford & Co were recorded at several addresses but by 1879 were at the Imperial Works, Brown Street. Between 1901 and 1923 saws ceased to be listed as a product, they appear to have had a wide product range and also were making files in 1901.
An item in a recently acquired 1932 catalogue of W Tyzack, Sons & Turner Ltd (above) confirms that they also made frig bobs which they described as stone saws, single hand. When this company began and ceased to make this type of saw is not yet known.
Quarrymen and their gangers owned their own tools. It appears that the quarry masters and firms bought the saws in batches and sold them to the men; this practice ended in 1939. The above prices represent a big portion of the fortnightly wage of a Bath stone quarryman in the 1930s.
Digging of Bath stone stopped in September 1939 and resumed in 1945 after the war ended; mechanisation soon followed. Three Mavor & Coulson arc shearers (basically tracked chain cutters) were delivered to Moor Park Quarry in 1948 to cut block from the rock. However these could not sever the back of the block from the rock and frig bobs were retained for this task.
Moor Park closed in 1952 and its equipment was transferred to Monks Park Quarry where the same practice continued until sometime around the mid 1950s when compressed air power was introduced. It was found that blocks could be snapped off at the back by a single set of plug and feathers inserted in a hole drilled in the natural parting under the bed at the front of the block.
At the Hartham Park and Clift quarries, it was found that, by drilling a series of deep holes at roughly 3 to 4 inches pitch along the line of an intended saw cut, hand sawing was greatly speeded up. This practice ended with the closure of Hartham Park in 1960 and the Clift in 1968. Park Lane Quarry was the last to be entirely hand worked; it closed in 1958.
Frig bob saws continued to be used by masons, it was still possible to buy them from Avery, Knight and Bowler Ltd of Bath as late as 1992 at a reputed price of £100 each – they now no longer sell them. However in 2006 the writer found an almost good as new one in a reclamation yard, which he secured for £20!
This article by David Pollard first appeared in TATHS Newsletter 101, Summer 2008.